#include "iic.h"
#include "systick.h"


//IIC初始化
void I2cInit(void)
{
    GPIO_InitTypeDef  GPIO_InitStructure;
    RCC_APB2PeriphClockCmd(IIC_RCC_port, ENABLE);
    
    GPIO_InitStructure.GPIO_Pin    = SCL_pin;
    GPIO_InitStructure.GPIO_Mode   = GPIO_Mode_Out_OD;                 //开漏输出    
    GPIO_InitStructure.GPIO_Speed  = GPIO_Speed_50MHz;
    GPIO_Init(SCL_port, &GPIO_InitStructure);

    GPIO_InitStructure.GPIO_Pin    = SDA_pin;
    GPIO_InitStructure.GPIO_Mode   = GPIO_Mode_Out_OD;                 //开漏输出    
    GPIO_InitStructure.GPIO_Speed  = GPIO_Speed_50MHz;
    GPIO_Init(SDA_port, &GPIO_InitStructure);
    
    delay_ms(10);
    GPIO_SetBits(SCL_port,SCL_pin);                                    //上拉
    GPIO_SetBits(SDA_port,SDA_pin);                                    //上拉
}

//数据端口配置为输出模式   
void SDA_OUT(void)
{
	GPIO_InitTypeDef  GPIO_InitStructure;
    
	GPIO_InitStructure.GPIO_Pin   = SDA_pin ;
    GPIO_InitStructure.GPIO_Mode   = GPIO_Mode_Out_PP;                 //输出
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_Init(SDA_port, &GPIO_InitStructure);
}
//数据端口配置为输入模式   
void SDA_IN(void)
{
	GPIO_InitTypeDef  GPIO_InitStructure;
	GPIO_InitStructure.GPIO_Pin  = SDA_pin ;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;

	GPIO_Init(SDA_port, &GPIO_InitStructure);
}

//iic延时使用
static void IIC_delay(void)
{
//    volatile int i = 1;	
//    while (i)
//        i--;
}

//起始信号  
void IIC_Start(void)
{
	SDA_OUT();
	SCL_HIGH;
	SDA_HIGH;
	IIC_delay();
	SDA_LOW;
	IIC_delay();
}
//停止信号    
void IIC_Stop(void)
{
	SDA_OUT();
	SCL_LOW;
	IIC_delay();
	SDA_LOW;
	IIC_delay();
	SCL_HIGH;
	IIC_delay();
	SDA_HIGH;
	IIC_delay();
}
/* 等待从机应答信号          */
/* 返回值： 0：接收应答失败  */
/*          1：接收应答成功  */
unsigned char IIC_Slave_Ack(void)
{
	SDA_OUT();
	SCL_LOW;
	IIC_delay();
	SDA_HIGH;

	SDA_IN();
	IIC_delay();
	SCL_HIGH;

	IIC_delay();

	if(SDA_READ)
	{
		SCL_LOW;
		return 0;
	}
	SCL_LOW;
	IIC_delay();
	return 1;
}

//发送一个字节   
void IIC_Send_Byte(unsigned char byte)
{
    unsigned char i = 8;
    
    SDA_OUT();
    while (i--)
    {
        SCL_LOW;                //拉低时钟开始数据传输
        IIC_delay();
        if (byte & 0x80)
            SDA_HIGH;
        else
            SDA_LOW;
        byte <<= 1;
        IIC_delay();
        SCL_HIGH;
        IIC_delay();
    }
    SCL_LOW;
    if(IIC_Slave_Ack()==0)
    {
        return ;
    }
}
/* 读取一个字节数据   */
/* 返回值：读取的数据 */
unsigned char IIC_Read_Byte(void)
{
    unsigned char i;
    unsigned char dat = 0;
    SDA_IN();
    for (i=0; i<8; i++)
    {
        dat <<= 1;
        SCL_HIGH;
        IIC_delay();
        dat |= SDA_READ;
        SCL_LOW;
        IIC_delay();
    }
    return dat;
}

/* 向寄存器写一个字节数据       */
/* SlaveAddress：从机地址       */
/* REG_Address：寄存器地址      */
/* REG_data：向寄存器写入的数据 */
void IIC_Write_One_Byte(unsigned char SlaveAddress,unsigned char REG_Address,unsigned char REG_data)
{
    IIC_Start();
    IIC_Send_Byte(SlaveAddress);
    IIC_Send_Byte(REG_Address);
    IIC_Send_Byte(REG_data);
    IIC_Stop();
}

/* 从寄存器读取一个字节数据 */
/* SlaveAddress：从机地址   */
/* REG_Address： 寄存器地址 */
/* 返回值：读取的数据       */
unsigned char IIC_Read_One_Byte(unsigned char SlaveAddress,unsigned char REG_Address)
{
	unsigned char REG_data;
    
	IIC_Start();
	IIC_Send_Byte(SlaveAddress);
	IIC_Send_Byte(REG_Address);
	IIC_Start();
	IIC_Send_Byte(SlaveAddress+1);
	REG_data = IIC_Read_Byte();
	IIC_Slave_Ack();
	IIC_Stop();
    
	return REG_data;
}
//连续读取两个字节数据   
unsigned short int IIC_Read_Two_Bytes(unsigned char SlaveAddress,unsigned char REG_Address)
{
	unsigned char H, L;
    
	H = IIC_Read_One_Byte(SlaveAddress,REG_Address);
	L = IIC_Read_One_Byte(SlaveAddress,REG_Address+1);
    
	return ( ((unsigned short int)H) << 8 | L) ;
}

#ifndef _iic_h_
#define _iic_h_

#include "stm32f10x.h"

#define  IIC_RCC_port   RCC_APB2Periph_GPIOB

#define  SCL_port   GPIOB
#define  SDA_port   GPIOB

#define  SCL_pin    GPIO_Pin_6
#define  SDA_pin    GPIO_Pin_5

#define SCL_HIGH          SCL_port->BSRR = SCL_pin
#define SCL_LOW           SCL_port->BRR  = SCL_pin

#define SDA_HIGH          SDA_port->BSRR = SDA_pin 
#define SDA_LOW           SDA_port->BRR  = SDA_pin

#define SDA_READ        ((SDA_port->IDR &  SDA_pin)!=0) ? 1 : 0

void I2cInit(void); 

void SDA_OUT(void);
void SDA_IN(void);

void IIC_Start(void);
void IIC_Stop(void);
unsigned char IIC_Slave_Ack(void);
void IIC_Send_Byte(unsigned char byte);
unsigned char IIC_Read_Byte(void);
void IIC_Write_One_Byte(unsigned char SlaveAddress,unsigned char REG_Address,unsigned char REG_data);
unsigned char IIC_Read_One_Byte(unsigned char SlaveAddress,unsigned char REG_Address);
unsigned short int IIC_Read_Two_Bytes(unsigned char SlaveAddress,unsigned char REG_Address);


#endif